After long-term use, 3d wall panels will inevitably have stains and wear marks on the surface, affecting the appearance and decorative effect. To address this problem, it is necessary to flexibly use a variety of means such as cleaning, repairing and protection according to the characteristics of the wall panel material and the degree of damage to achieve effective repair.
When facing surface stains, the material of the wall panel must be clarified first. 3d wall panels of different materials have different tolerances to detergents. For 3d wall panels made of PVC, because their surface is relatively smooth and water-resistant, you can use a mild neutral detergent and wipe it gently with a soft damp cloth. When wiping, you need to follow the direction of the wall panel texture to avoid scratching the surface by rubbing back and forth. Although bamboo and wood fiber wall panels have a certain degree of waterproofness, overly wet cleaning methods may cause the board to expand and deform. Therefore, it is recommended to use a slightly damp soft cloth to wipe with a small amount of detergent, and then use a dry cloth to absorb the moisture in time. For 3d wall panels made of resin, because their surface hardness is relatively high, you can use a slightly more powerful detergent appropriately, but you should also avoid using rough cleaning tools to prevent scratches on the surface.
For some stubborn stains that are difficult to remove with ordinary detergents, special treatment methods are required. If it is an oil stain, you can try to use a small amount of alcohol or a special degreasing agent, apply it to the stain, let it stand for a while, and then gently wipe it with a soft cloth. However, when using organic solvents such as alcohol, be sure to first test it on a small area in an inconspicuous part of the wallboard to confirm that it will not cause corrosion or discoloration on the wallboard surface before using it on a large area. If it is a pigment stain such as ink or colored pencils, you can use an eraser to gently wipe it, but pay attention to the strength to avoid excessive force that may cause the wallboard surface to dent. For the remaining traces of tape on the wall, use the hot air setting of a hair dryer to soften the tape marks, then carefully remove it with a soft cloth, and finally wipe the remaining part with a detergent.
When 3d wall panels are worn, it is relatively simple to deal with minor scratches. If the surface coating is worn, for colored wallboards, you can use crayons or paints similar to the color of the wallboard to fill it. After applying evenly, gently polish it with fine sandpaper to make a smooth transition between the repaired area and the surrounding surface. If the three-dimensional texture on the wall panel surface is slightly worn, you can use special caulking agent or putty to fill it. After it dries, use tools to carve and repair it according to the shape and direction of the original texture, and finally spray a protective paint that matches the color of the wall panel to restore the overall beauty of the wall panel.
For more serious wear or damage, such as large-scale paint loss, cracking or even partial detachment of the wall panel, partial replacement is required. First, find a replacement panel that matches the material, color and texture of the original wall panel. When removing the damaged part, be careful to avoid secondary damage to the surrounding wall panels. When installing new wall panels, ensure that the joints are tightly fitted. You can use special wall panel glue or buckles to fix them. After installation, carefully treat the joints, fill the gaps, polish them flat and spray them with protective paint to make the newly installed wall panels blend seamlessly with the original wall panels.
Daily maintenance is an important measure to prevent stains and wear on 3d wall panels. In daily life, avoid sharp objects hitting the wall panel surface to prevent scratches or damage. Clean the wall panels regularly. Use a clean soft cloth or duster to remove surface dust and keep the wall panels clean and tidy. In addition, you can apply a layer of special protective wax or protective agent on the surface of the wall panels every once in a while to form a protective film to enhance the wear resistance and stain resistance of the wall panels and extend their service life.
If you are not sure about the repair of 3d wall panels, it is recommended to seek help from professionals. The professional maintenance team has rich experience and professional tools to accurately judge the degree of damage to the wall panels and take the most appropriate repair method. They can not only guarantee the repair effect, but also avoid further damage to the wall panels caused by improper operation, saving time and energy.
The surface stains and wear problems of 3d wall panels after long-term use can be effectively restored to the beauty and decorative effect of the wall panels through correct cleaning methods, targeted repair methods, daily maintenance and professional treatment when necessary. As long as you master the scientific treatment method, you can keep the 3d wall panels in good condition after long-term use and continue to add unique charm to the space.
